RSCO Hand Riveter Nut Tool model HN-096

Rivet Nut

The various components of the rivet bead include:

• Head Tools
• Cavity
• pin
• The body
• Category
• Save pin
• Plastic dummy handle
• Handle holder

How to operate the riveting nut is as follows:

• On the sheet we will pierce the drill with the desired size.
• Fit the appropriate rivets with the perforated sheet size in the perforated section of the sheet.
• We put the riveting nut series into the sheet hole and, by opening the two sets of device, the riveting operation is performed.

Maintenance of Rivet Nut:

• To prolong the life of the riveting nut, clean the appliance every time and do not rub any dust or grease.
• The rifle nut should be serviced by an authorized service.

Observing the following points in the individual environment and in the work environment: When using this machine, the needle nut is required:

• The work environment is free of any contamination.
• The die-casting machine is not an electric insulator. Please be careful when using.
• Do not use the rivet nut during sleepiness
• Use safe work clothes.
• Do not use any riveting tool in the event of damage or fracture.
• Do not hit the rifle nut
• Make sure that the nut is straight.

Read more about other products of the industry:

• For cutting of all kinds of plastic or polypropylene tubes, shear shear shears or shear shears are used.
• pex pipe fittings are pressed by a pex pipe press (including pex manual pipe press, a pex, pex pipe press, and a hydraulic press of a pex pipe).
• It is worth noting that in new years, metal pipes, galvanized, have been used, which are made by hand tools or electrical workpieces.
• It should be noted that in the main networks of pipelines, pex pipes are used. To open these types of pipes, you can use the roller of the pex industrial pipe.
• It is worth noting that the five-layer pipes bend with a five-layer tube bending machine and riveted with a pex pipe piercing device.
• To test the pipe after the completion of the plumbing. When the pipes are filled with water, after testing the pipes and closing the openings, the pipes are tested by plumbing testing machines, which include (manual pump test and electric pump test).
• To leak the pressure pipes, we introduce the industry-leading mini-leak detector. The industry has gas leak detectors.
• For repairs of polyethylene welding machines, polyethylene boiling heat, green tube iron, pump testing machine,pex pipe presses, welding inverters and leak detectors, please refer to the sales office of the industry.
• Stainless steel extruder is also used to repair pipe and fittings of pe.
• The high-pressure welding extruder of the industry is used as a welding pipe and polyethylene fittings.
• Due to the fact that steel and galvanized pipes are used today, electric devices are used to carry out these types of pipes.
• The industrial scrubber is used to peel polyethylene pipes.
• The squzeer is used to block the transmission of pe pipes
• Cutting of pe pipes from a size of 25-160 mm is done by pipe on guillotine.
• Multi-clamp is also used to hold polyethylene pipes during welding.
• The clamping of polyethylene pipes is used to hold the polyethylene pipes at the welding time.
• Welding Industry has the ability to weld various types of plastic surfaces in PVC, PP, polyethylene.
• The Rossabor copper tube has the ability to cut all kinds of copper and aluminum pipes. And Ripper is a steel wire mesh made of high alloy steel
• Hydraulic bender The five-layer industrial pipe is used to bend all kinds of steel, steel, copper and aluminum pipes.
• Hydraulic polisher is used to get all kinds of industrial money.
• The hand pump is used for winding up to a maximum of 1.9 times

Hand Riveter Rivet:

Information:

• Can be used horizental and vertical.
• It is so strong againt destruction.
• It is used for pressured plastic and metal fittings.
• We can use it in car industry.
• It is available in these weights 2.6 and 0.6.
• Made in Japan.
• Contact us for more information.