RSCO plastic pipe cutter ROCUT PCP160

• The size of the large size of this tool is a trunk of a base pipe of 40-160.
• The body material of this pipe is multi-purpose die cast aluminum.

Three-piece triple-mounted metal handle

• How to operate this machine is hand-held.
• The pipe has three pockets of base.
• Three-Duplex installation method.
• The pipe is marked as needed and is cut by a pipe cutting machine.
• This machine, in addition to the cutting of three-piece duct with a 15-degree duct, at the end of the tube tool for the multi-purpose cut-off duct.
• Immerse the capped duct only with non-acid lubricant uniformly.
• Press the tube end of the multi-purpose pipe to the finished end of the fitting
• To control the longitudinal expansion, pull it about 1 cm away from the end of the tube.
• You can use this pen to make sure.
• Only a pipe can be used to get such a shear.
• However, it is possible that obsolete methods of using a toothed saws, with the help of a grooved groove, and by wrapping the paper around the plumbing tube to find the correct cut-off line in some way.
• However, the best and most principle-based approach that quickly comes with ease and reliability is the use of the tube.

Patching the cutting location on a three-piece machine:

• The lacking of a socket in all tubes and stencil cases is an oblique mode.
• This feature makes the work of joining the components more comfortable with each other.
• And at the same time prevent possible damage to the sealing ring or its removal from the socket.
• It is therefore advisable to obfuscate the cut-off after cutting the cut edge.
• It is not recommended to use Sohan to do this. The angle of the perforated section according to the existing standards can be 15 to 45 degrees.

Warning:

• Uncontrolled discharge of pipes and fittings is not allowed at all.
• Avoid throwing pipes and fittings.
• Avoid moving tubes while they are on the ground.
• When working with the device, have sufficient information on how to operate it.
• Select the correct jaw size for work
• Please note that the machine is free from any oil and dust, which will increase the life of the machine.

Observing the following points in individual safety and safety at work is required:

• Keep the environment clean and free from any dust or oil.
• The presence of any abnormalities in the environment will cause problems.
• This is an electric insulating device. Please be careful when using.
• The use of grease and oil for psychoanalysis is prohibited.
• When working in the premises of buildings, the pipes should be kept away from soil and building materials and prevent the entry of gravel into them.
• Pipes are arranged regularly and avoid contact with sharp objects and wins
• Avoid bending pipes.

Read more about other products of the industry:

• The industrial steamer is used to block all types of pipes and fittings in water and wastewater, oil, gas and petrochemicals.
• The wind turbine has the ability to test the pipe.
• Hand-operated stopper for testing all types of ppr, pe and PVC pipes.
• The handpiece is capable of tapping all types of pipe fittings.
• Pipe fitting wrench is used to keep all types of ductile pipes.
• The copper pipe has the ability to cut all kinds of copper and aluminum pipes.
• Welding equipment of PE is a polyethylene pipe and polyethylene fittings.
• Polyethylene pipes can be welded to the welded polyethylene.
• ppr welding machine, ,is a device for carrying out the piping of ppr or plastic pipes.
• These ppr pipes can be cut with industry-saving ppr cutter (or cutters tube cutters, pipe cutter).
• The polyethylene welding iron has a polyethylene tube and polyethylene fittings.
• The Industrial Pump Test Machine has been designed with a unique design, light weight to test and test the piping of pipelines and reservoirs.
• R.S.co Industrial Company is able to repair the water piping test machine. So you can refer to the office of Rastgar Industry for the repair of the water pipe testing machine.
• To leak the pressure pipes, we introduce the industry-leading mini-leak detector. The industry has gas leak detectors.
• pex pipes, which can be pressed withpex pipe presses (pexpipe presses,pex pipe hydraulic presses, pex pipe presses, pex pipe presses), one of the most modern plumbing systems.
• The first layer of the pex pipe, which can be pressed by pressing the pex pipes of the industry. Which forms the outer surface of the layer.
• To repair the pex pipe presses you can refer to the office of Rastegar Industry. Because is capable of repairing pex pipe presses.
• It should be noted that it can be detected by the hand leak detector to detect pipe fractures.
• To test the pipes after the completion of the plumbing When the pipes are filled with water, after testing them and closing the span, we test the pipes by the industry pump testing machine.
• It is worth mentioning that metal pipes and galvanized pipes are also used today to be used for manual handling of electrical pipes.

Information:

Push-fit roller cutter (tripled task legged):

• Able to hold, cut and chamfer all types of push-fit pipes and attachments
• Made from dia-cast aluminum
• Big size: 40-160 mm
• The design of this roller cutter (multi task) is the way that it won't be locked on the pipe, instead the pipe will be fixed in the tripled leged
• Adjustable metal handle for adjusting blade depends on the size and thickness of the pipe
• Includes ISO9001 and CE from Europe unioun
• Includes after sale service (only on used tools)
• Contact us for more information.

plastic pipe cutting_plastic pipe cutter rocut_pipe cutting and pipe chamfering tool_rocut plastic pipe cutter_chamfering tool insent adaptor_push fit chamfering tool_pushfit pipe roller cutter