RSCo manual pump tester model TP65

Pump test 0-60 bar. Metal industry

Tips:

This manual pump test is used to test all types of water pipe, sewage and reservoirs, and so on.

The procedure for testing the pump is as follows. First, the whole environment you want to be tested should be completely watered.

After being fully filled, connect to the pump test system.

How to work with the plumbing test machine:

• The pump test environment should be filled with water and free of any air.
• We test the electric pump according to the test method to the corresponding location of the system.
• After the water pump has been pumped into the system and the water has not been flushed out and pressurized during the specified time, the tube pump test shall remain under pressure.
• The tank of the electric pump test pump is completely filled with water.
• After pushing up and down the handle, you can press the system.
• Be aware of all the above steps.
• Please note that the plunger shaft of the plumbing test must always be lubricated.
• To ventilate the water pipe testing machine below 30 bar, be sure to carefully observe the following points.
• If the reservoir is full of water, make sure that the shaft that is raised and lowered by the lever handle is refractory from the grease.
• If the test shaft is impregnated with grease, it will quickly disappear. And maybe it will not output to the test system due to its lack of functionality.
• After the test, be sure to rinse the entire system with gasoline and avoid water remaining in the entire set.
• If the test steps are carried out with spilled water or impregnated water, these solvents will lock the inlet valves of the pump test and prevent the pump test screw from working.

Important points for the 60-time pump test device:

• With all the tips for testing pumps below 60 times, the same points apply to this pump test.
• But the distinctive feature of this pump test is the self-testing of the pump.

How to breathe a 60-fold plumbing test machine:

• To pump the pump 60 times to the boiler, first open the handle from the up and down shaft and fill it in the cylinder.
• Then place the shaft soaked with grease in place.

Knowledge:

• The Industrial Pump Test Machine has been designed with a unique design, light weight to test and test the piping of pipelines and reservoirs.
• Rastegar Industrial Company is able to repair the water piping test machine. So you can refer to the office of Rastgar Industry for the repair of the water pipe testing machine.
• To leak the pressure pipes, we introduce the industry-leading mini-leak detector. The industry has gas leak detectors.
• PEX pipes, which can be pressed with PEX pipe presses (PEX pipe presses, pex pipe hydraulic presses, pexpipe presses, pexpipe presses), one of the most modern plumbing systems.
• The first layer of the pex pipe, which can be pressed by pressing the pex pipes of the industry. Which forms the outer surface of the layer.
• To repair the five-layer pipe presses you can refer to the office of Rastgar Industry. Because Razabat is capable of repairing five-layer pipe presses.
• The task of the outer layer of a pex pipe is to protect and maintain a self-contained pex pipe (which can be emitted by a pex pipe).
• The outer layer of this pex pipe (which can be bended by a pex pipe bending spring). This layer creates adhesion between the layer between the outer layer and the third layer.
• The third layer of thepex pipe (which can be riveted by the pex pipe piercing) is very thin aluminum.
• The task of the third layer of the pipe is the pex pipe control of the temperature or the temperature of the current water in the pex pipe (which can be bended by the pipe of the pex pipe, the industry is bending these pipes).
• And the pipe retainer against the deformation of the pex pipe (which can be used to open the tube from the pex pipe open roller) is extremely high temperatures.
• It should be noted that it can be detected by the hand leak detector to detect pipe fractures.
• To test the pipes after the completion of the plumbing When the pipes are filled with water, after testing them and closing the span, we test the pipes by the industry pump testing machine.
• These pipes are cut by ppr pipe cutter or foliage shears ,pipe cutters.
• It is worth noting that metal pipes and galvanized pipes are also used today to be used for manual handling of electrical pipes.

Industry Repair or Maintenance

• To prolong the life of the water pipeline system, clean up the use of the machine after each use and use any oil and dust.
• The machine must be operated by an authorised service service.
• It is necessary to use a strong safety pressure pump test in the workplace and personal safety.
• Clean and dust the work environment clean and free of all oil and dust.
• Any anomalies in the workplace will cause problems.
• The unit test unit is not thermal. Please check when you use it.
• Use clean water .
• Wash all the set of plumbing testing thoroughly with diesel after each load.
• avoid pushing too much of the quorum over the water plumbing test apparatu.
• don't Use manual pump test when you are sleepy.
• Use safety.
• If you don't see a breakdown or fracture, don't use the water pipe test machine.
• Do not enter the pump test device.

Information:

RSCo high pressure metal test pump (0-60Bar):

• Able to test all under pressured systems (0-60 Bar).
• Includes furance colored thick and strong tank.
• Includes tank smoother with italian one way tap.
• Includes full aluminum sylinder (strong and light high pressure).
• Includes test and warranty and 10 years after sale service.
• Includes ISO9001 and CE from Europe unioun standards.
• For more info contact via webpage.

,test pump,hydraulic pressure test pump ,pressure testing pump,manual testing pump, test pump for testing pump,hand water test pump,manual pressure testing pump