Coil Spring Compressor
Information :
We use Coil Spring Compressor is used for limited spaces and to open and close spiral spring .
Jaws and scews is made of chromium mobidemn .
Springs can be used for vehicles ....
Valve spring compressor
Information :
We use Valve spring compressor to open and close valve of engine neutral the spring pressure the release it and takes out the valve .
Able to work with small , big cars .
Maximum...
oil filter pliers
Information:
We use oil filter pliers to open small cars and trucks.
Working Range : 120 inch .
Anti-slip while working.
General Length : 260 mm
Made of Vanadium Chromium.
Including anti-slip and...
Air Stapler
Information:
Can be used for wooden pallets, ceiling sconces, wooden wall sconces and floor coverings, sofa upholstery, etc. due to its high strength
Magazine capacity: 160 staples
Pneumatic operating...
Air Nail Gun
Information:
Can be used for wooden pallets, ceiling sconces, wooden wall sconces and floor coverings, sofa upholstery, etc. due to its high strength
Magazine capacity: 100
Type of nail used: SK
Hardened...
Pneumatic Ratchet Wrench
Information:
To loosen and tighten bolts with high-strength
Pneumatic operating system
Suitable for industrial work, factories and repair shops
Torque: 122 Nm
Ability to tight 13 mm screws...
Flow meter
Information :
We use Flow meter to count the liter depending on concentration of liquid.
Icluding Viscosity with long life and resistant.
Flow rate: 20-120 lit/min
Accuracy: +/- 0.5%
Can be installed...
RSCO needle Cable Crimping
Information:
Used for pressing all kinds of copper, aluminum, etc. cables
Making electrical connections without the need for soldering
Steel jaw
Pressing size: 8 - 80 mm
Plastic-coated...
RSCO Jack pallet
Information:
It is used to move and transport cargo in the warehouse.
capacity: 2 tons
Minimum lifting height: 85 mm
Maximum lifting height: 195 mm
The length of the forks: 1220 mm
The inner width of...
RSCO electric forklift
Information:
The electric forklift is used to move and lift the load in the warehouse.
Tolerable capacity: 2 tons
Voltage 220 volts and frequency 50 Hz
Power: 2.2 kW
Maximum lifting height:...
Hammer drill
Information :
This electric hammer drill is used to pierce concrete and wall.
Speed without load : 0 - 2800 round per minute.
Dust proof ball bearing that increase lifelong of device
Power : 750 w...
information :
Manual industrial hydraulic press
able to use 0.5-100 kg
3-28 cm diameter
2-20 cm inside diameter
0.5 mm finesse
manual industrial hydraulic press,hydraulic press,manual hydraulic press,hydraulic press...
Cast iron Electrode
Information:
Used to generate electricity to perform welding steps
Used for welding cast iron and cast iron parts
Welding modes: Flat, horizontal, vertical and upward welding
Material: cast iron...
Silver Brazing Alloy
Information:
Used for welding two pieces of silver, two pieces of copper and two pieces of non-homogeneous metal
Used in radiators, cold stores, refrigerators, chandeliers, etc.
15% silver
Inlet...
CO2 Welding Wire
Information:
Used for uniform welding
For welding of steel building migs and pipe steels and other gas mixtures such as argon gas 5 to 25% using CO2 gas
Used in alloy building steels, pipe steel,...
Cut off saw
Information :
Cut off saw is suitable for cutting tough material like iron and profile.
Speed : 3900 round per minute
Power : 2100 W
Sheet diameter : 355 mm
Suitable for cutting pipe , metal , profile ,...
Mixer Drill
Information :
Power Screwdrivers Paint Mixer is powerful device that is used to mix building material like paint ....
This device is suitable for building operations, industry and nutrition industry....
Electric soldering gun
Information :
We use Electric soldering gun to melt solder and connect metal part .
Electric soldering gun is used for powerful and high speed .
Body made of fire proof metal
Power : 180 w
With...
Ronix eletric Impact Wrench
Information :
Electric Impact Wrench is used is used to open and close screws and nuts in a shot period of time .
Dimension : 21 × 8.5 × 29.5 cm
Maximum speed : 2200 round per minute ....
