KENZAX PEX pipe manual press

IntroducingPEX pipe manual press:

• PEX pipe manual press is used to press pipes and fittings.
• It is worth noting that PEX pipe manual press are pressed with five-layer pipe presses.
• These presses include manual PEX pipe manual press,PEX pipe manual press hydraulic pipe presses,PEX pipe manual press, and PEX pipe manual press.
• All five-layer flexible pipe presses are capable of pressing all pipes and fittings (SuperPip, NewPipe, Unicip Pip)

Tips on Pressing the Five-Layer Pipe Industry:

• Firstly, the PEX pipe can be cut with a scissor (or pipe scissors, pipe scissors, pipe shears, green tube scissors, green tube cutting shears)
• Cut it to the desired size with a caliber tool inside (it can be bended through the PEX pipe by bending the pipes)
• Slightly loosen and using the blades at the end of the caliber, with the rotary motion of the inner wall of the five-layer pipe (which can be riveted by rolling the five-layer pipe into these pipes)
• It is very important to do this because the PEX pipewall can be bended with the PEX pipe tube bending spring before winning the calibration.
• Therefore, the rubber thread may break the connection during installation, which can lead to false positives and leakage of water.
• In the end, after the first caliber, the connecting pin of thePEX pipe (which can be pressed by a five-layer tube press, which includes a PEX pipe, PEX pipe electric tube, manual, and hydraulic press)
• In the installation procedure for fittings such as couplings, it is necessary to calibrate the PEX pipe pipes (which are installed with PEX pipe) before installation.
• Then, the PEX pipe can be fitted with a manual press of a PEX pipe industrial pipe.
• These five-layer tubes can be easily opened with the roller opening of the five-layer industrial pipe.
• After the completion of the piping, when the pipes are filled with water, after pipe drainage and the opening of the openings, we test the tubes by the plumbing test devices (in the form of a manual pump test device and an electric pump test device).
• To detect the pipe fault, the leak detector can be detected by the professional professional handheld researcher.
• Also, Razgrad has gas leak detectors.

How to set up the PEX pipe manual press PEX pipe w32 industry salvage:

• After removing the manual press from the box, select the jaws from the size of the connection and the corresponding pipe and press on the main jaws.
• After placing the jaws, close the main mandrel screws.
• When the initial point of the jaws collapses, the spacing within the press in the W model is 21-25 cm and in the model A is 31 to 36 cm.
• The permitted distance from the handle is 21-25 cm in the short position and in the 31-36 cm long position.
• The greater the gap between the sections causes the press to break and the less it will cause the seal to fail.
• If the distance between the sections is greater or less, it can be very accurate with the screw head and can be adjusted by rotating about 1.4 turns.
• the adjustment knob (12) is locked, the screw (13) can be opened in three rounds and the set will be released after opening the screw.
• After locking the screw, adjust the screw (13) to its original state and restart it.

How to make press in a manual press machine PEX pipe laminating pipe Industry:

• Open the jaw completely after preparation, and then calibrate the connection into the jaw after calibration.
• The block of the fitting should be placed at the edge of the press jaw.
• Then close the presses so that the corresponding connection is fully pressed.
• During the press, the main categories should be closer together.

Nailing and maintenance of manual presses PEX pipe resilient tube Industry:

• To extend the life of the five-layer, five-layer pipe, after the work is completed, place the device in the appropriate box.
• If you do not press, open the jaws from the press and place inside the box.
• The jaw pressure shaft is opened to keep the press pressed and unpressurized.
• Do not place the relevant presses and jaws in the vicinity of the soil, as it will cause faster erosion.
• Maintain the jaw presses and keep it clean.
• Try pressing with lubrication or gasoline related jaws.

Explanations:

This press machine with many efforts of innovators and engineers of this company with the best technology in the world and a variety of CNC and NC machines has been developed by the hot Forging method (with the highest alloy steels) and  produced this valuable product for the first time in their name, and this product is another honor from this company.

Information:

RSCo static PEX pipe manual press:

• Ability to press 5 layered pipes and attachments.
• Steel jaws in 4 sizes: 16, 20, 25 , 32.
• Sealing warranty till 16th pressure.
• Metallic strong box.
• Guide book with Hex wrench screws.
• Iso 9001 and CE standards.
•  1year sealing warranty of RSCO.

pex pipe manual press,hand press tool for pex-al,pex pibe,hand press tool for pex pipe,pipe maual press,manual pipe press,pipe manual press tool,manual press tool kit for pex,al-pex