Air Drill
Information:
To perform all kinds of high power drilling
Size: 13 mm (9.16 inch)
Speed in idle mode: 600 rpm
Total length: 262 mm
Pneumatic operating system
Working pressure: 0.62 Mpa
Hose size: 3.8 inch...
HEZBURN two Leg Puller
Information:
Used to remove and place all kinds of industrial pulleys
Made of hardened steel
arm length: 100 mm
Workable diameter: 90 mm
Impact resistant
Middle screw length: 100 mm
Made in...
Socket weld cap 1/2"
Information:
PVC pipe welding machine.
The alloy of this socket is first-rate aluminum covering with furnace silver Teflon.
In sizes: 1/2" = 20mm.
This welding machine is used to weld all kinds...
RSCo metal calibrator
Information:
This calibrator is used for calibrating (measuring) all kinds of PEX pipes.
These PEX calibrators are made of alloyed steel.
Size: 50 mm
Because of the big size and easy operation,...
RSCo Pipe test plug
Information:
To test all types of PVC, HDPE and Push-fit pipes
Testable sizes: 45 - 125 degrees
45 degree angle for easy working
Flexible rubber
Manual operation system
Contact us for more...
Pencil Tip Nozzle
Information:
Can be installed on a series of 1600 and 3400 watt direct industrial heat guns
For welding plastic plates to each other, repairing polyethylene tanks, repairing cracks in the walls of...
Battery Powered Cable Cutter
Information:
Used for cutting copper, aluminum, etc. cables
High strength steel jaw
Ability to install jaw presses of all types of aluminum and steel pipes and fittings
Ability to install...
Electronic Needle Nose Pliers
Information:
Used to grip, bend and cut wires and cables
Used in electrical work
Suitable for small pieces
Handles with soft and non-slip cover
Made of high strength chromium and...
Tongue and Groove Pliers
Information:
Used to open and close pipes as well as bolts and to grip and tighten tools and objects with unusual shapes
Handles with soft, antiperspirant and non-slip covers
Ideal for...
End Cutting Nipper Pliers
Information:
Used for cutting, twisting, bending wires and also in reinforcement
Total length: 300 mm
Ideal for confined and inaccessible spaces
Made of high strength steel
Handles with...
Manifold gauges hose 60 inch
Information :
Manifold gauges hose is suitable for connecting manifold gauge to the device .
Length of Manifold gauges hose is 150 cm .
Equippd with 3 hose in red , blue and yellow...
Push fit polyamide sheet
Information:
We use this part for back of rotating push fit sheets.
Made of polyamide with fibers.
Can be used with different types of pipes.
Made in IRAN
Contact us for more information.
Hole Saw Drill Alloy
Information :
Hole Saw Drill Alloy includes notch for a clean cut.
Able to work with wood , particle board , MDF etc....
Made of high resistant steel.
Equipped with Tungsten carbide for regular...
Slovenia Level
Information:
Used to measure and detect horizontal and vertical surfaces
Aluminum body with anti-corrosion epoxy
Has a magnet
Metal body and impact resistant
length of magnet : 300 mm
Width of magnet :...
Curved Tip Awl
Information:
It is used in bookbinding and sewing book covers, and in embroidered shoes to pierce leather and pass needles
Handle with antiperspirant and non-slip plastic cover for easy operation...
Industrial gasoline test pump
Information:
For testing blocked systems
Max outlet pressure: 120 Bar
Power: 1.5 HP
Input voltage: 220-230 V
External coupling
Electromotor body with togetherness piston pump
5-years...
Industrial brush
Information :
Suitable for removing mass ,paint , welding tears , deposition and rust .
Made of hardened steel with high percentage of carbon.
Outer diameter : 100 mm
Size of this Industrial brush :...
Allen Wrench Set
Information:
It is an L-shaped hexagonal device used to loosen and tighten Allen screws
Ideal for confined and inaccessible spaces
Ball end
Size: 1.5 - 2 - 2.5 - 3 - 4 - 5 - 6 - 8 - 10 mm
Made of...
Desk vice clamp
Information :
We use Desk vice clamp to hold parts for easy operation.
Working Range : 100 mm.
Size : 100 mm
Made of Carbon Steel.
Fast and percise opening and closing because of the trapezoid shape....
Inverter Plasma Machine
Information:
To cut steel or other metals (sometimes some other materials) in different diameters using a torch
Maximum cutting thickness: 30 mm
Current range: 15-50 amp
Power voltage: 220V...
